
Performance Clutch Pin - Grooved
- The BMW factory pin is made from plastic which has very little heat resistance, which causes premature wear on the pin.
- AGA Tools has reproduced this part to factory from a sturdy silicon bronze, making it heat resistant and durable.
- The AGA Performance Grooved Clutch Pivot Pin saves customers from having to do frequent, costly repairs by providing a life-long solution to factory parts.
Ordering from Europe? Click here to buy from our European distributor KOED
Specifications
Models This Product Fits
525i M50 | E34 | 525i, Wagon | E39 | 525Xi | E60 | X3 xDrive30i | E83 | 335Xi | E90 |
530i (V8) | E34 | 530i | E39 | 530Xi | E60 | Mroadster S54 | E85 | M3 Sedan | E90 |
325is | E34 | 540i | E39 | 550i | E60 | Z4 2.5i, 3.0i/si | E85 | 328i xDrive Wagon, Coupe | E91 |
318i, ti, is, iC | E34 | 528i, Wagon | E39 | M5 | E60 | Z4 3.0si Coupe | E86 | 325Xi Wagon | E91 |
328i, is, iC | E34 | 323i,Ci/Conv., Wagon | E46 | 528i, Xi, ixDrive | E60 | Mcoupe S54 | E86 | 328i, Xi Wagon | E91 |
M3 B30 | E34 | 328i, Ci | E46 | 535i, Xi | E60 | 128i Conv. | E88 | 328i, Xi Coupe | E92 |
M3 B32 | E34 | 330i, Ci, Xi, Ci Conv. | E46 | 530Xi Wagon | E61 | 135i Conv. | E88 | 335i Coupe/ xDrive Coupe | E92 |
323is, iC | E34 | 325i, Xi, Ci, Ci Conv. | E46 | 535i xDrive Wagon | E61 | Z4 sDrive 30i | E89 | M3 Coupe | E92 |
M Roadster S54 | Z3 | 325i/Xi Wagon | E46 | 645Ci, Ci Conv. | E64 | 325i, Xi | E90 | 335Xi Coupe | E92 |
M Coupe S54 | Z3 | M3, M3 Conv. | E46 | 650i, Conv. | E64 | 330i, Xi | E90 | 328i Conv. | E93 |
MRoadster S52 | Z3 | 525i N52 | E60 | M6 Conv. | E64 | 328i, Xi | E90 | 335i Conv. | E93 |
Mcoupe S52 | Z3 | 545i | E60 | 128i & 135 | E82 | 335i | E90 | M3 Conv. | E93 |
Z3 1.9, 2.3, 2.5i, 2.8 | Z3 | 525i M54 | E60 | 135i | E82 | 328i xDrive | E90 | X5 3.0i | SAV |
Z3 Coupe 2.8, 3.0 | Z3 | 530i M54 | E60 | X3 2.5i, 3.0i/si | E83 | 335i xDrive | E90 |
Part Included
Quantity | 1 |
---|---|
Part # | AGA-CPP-223-328 |
Description | Performance Clutch Pin - 328 - Grooved |
Customer Reviews
Installation Instructions
These instructions are for experienced technicians only. This job should only be done by an experienced technician. If instructions are need to remove stock components refer to All Data, Mitchel or Factory Manual.
STEP 1
o install the pin, simply place pin in hole. Place socket that fits over dome without touching the end of pin. 15mm 12 point socket works well for this. Lightly tap socket with extension until the pin is fully seated. It is normal for the pin to fit tight. DO NOT hit end of pin with a hammer, punch extension, etc
